Blog - Sanphorus

Blog

by 0 Comment

GentleLASE PRO Preventative Maintenance Procedure

WARNING – SHOCK HAZARD!!! The high voltage capacitor in the GentleLASE PRO laser retains LETHAL voltages and must be safely discharged, before working near the laser head or inside the HV section for any reason. This procedure must be performed only by those technicians who are familiar with the precautions required when working with high voltage specific […]

by 0 Comment

GentleLASE Bubble Circuit Calibration Procedure

Connect the MGL HP delivery system to GentleLASE laser. Install cryogen canister into the laser per the procedure in the Operator’s Manual. Turn on the GentleLASE laser. System should display a warm-up message. Warm-up takes approximately 20 minutes. The DCD unit must complete warm-up prior to the following tests! The cryogen is fully warmed up […]

by 0 Comment

MGentleLASE Calport Calibration Procedure

CAUTION!!! During this procedure it is possible that the laser may fire, emitting laser radiation. Therefore SAFETY EYEWEAR must be worn. The eyewear must have an optical density of at least 5.8 at 745 – 765 nm. The high voltages present in this system are LETHAL. This procedure must be performed only by those technicians […]

by 0 Comment

MGentleLASE Aiming Beam Alignment Procedure

CAUTION!!! During this procedure it is possible that the laser may fire, emitting laser radiation. Therefore safety eyewear must be worn. The eyewear must have an optical density of at least 5.8 at 745 – 765 nm. The high voltages present in this system are LETHAL. This procedure must be performed only by those technicians […]

by 0 Comment

MGentleLASE Focus Lens Replacement Procedure

NOTE: Exercise extreme care. Cleanliness of optics is essential. Refer to Service Procedure 8503-01-0060 for optic cleanliness. Refer to drawings 7122-00-3298, 7122-00-3300 and 7122-00-3325 for specific details. CAUTION: The high voltages present in this system are LETHAL. This procedure must be performed only by those technicians who are familiar with the precautions required when working […]

by 0 Comment

MGentleLASE Laser Rail Alignment Procedure

CAUTION!!! During this procedure it is possible that the laser may fire, emitting laser radiation. Therefore SAFETY EYEWEAR must be worn. The eyewear must have an optical density of at least 5.8 at 745 – 765 nm. The high voltages present in this system are LETHAL. This procedure must be performed only by those technicians […]

by 0 Comment

MGentleLASE Head Detector Calibration Procedure

CAUTION!!! During this procedure it is possible that the laser may fire, emitting laser radiation. Therefore SAFETY EYEWEAR must be worn. The eyewear must have an optical density of at least 5.8 at 745 – 765 nm. The high voltages present in this system are LETHAL. This procedure must be performed only by those technicians […]

by 0 Comment

MGentleLASE HVPS Calibration Procedure

CAUTION!!! During this procedure it is possible that the laser may fire, emitting laser radiation. Therefore SAFETY EYEWEAR must be worn. The eyewear must have an optical density of at least 5.8 at 745 – 765 nm. The high voltages present in this system are LETHAL. This procedure must be performed only by those technicians […]

by 0 Comment

GL Pressure Verification Procedure

NOTE: This Service Procedure is for GL laser systems with a DCD Pressure sensor installed. Turn on the laser system and enter into Maintenance Mode. Ensure a DCD canister is installed. The canister must be fully warmed before continuing this procedure. Attach the Pressure Transducer terminals to the 300mV jack of the DVM. Insure that […]

  • 1
  • 2
    Contact Us
    close slider
    Cart